Categories: Water Filter, Vessel, Softner, Accessory-32
Product Short Description: More effective. Also refer new tec grade if ur requirement to absorb poisonous gases RXSOL-24-1905-025
Product Description:

A highly porous material, this material can have a surface area significantly over 200 square metres/g. Very suitable for use as a filter of fluoride, arsenic and selenium in drinking water

Product Application:

It has a high surface area which adsorbs vapors without any change in form. Will not soften or disintegrate easily when immersed in water.

Dew points to -40°F and lower may be achieved depending on dryer design and operating conditions.

The 1/8” (2-5mm) bead is the size most frequently used in regenerative dryers.

The 3/16” (4-8mm) bead is used when pressure drop and surface area requirements fall between 1/8” and 1/4” material.  It is suitable for most systems.

The 1/4” (5-10mm)  is used both as a pre-bed material to support large desiccant beds or as a buffer for silica gel beads. Pressure drop is slightly lower than 1/8” (25mm) material. 

If size is not known or specified, the 1/8” (2-5mm) size is usually satisfactory.

Product Dose:

Product Benefits:

  1. High adsorption capacity. With high surface area and excellent pore distribution, has a high water adsorption capacity. This reduces initial cost, energy consumption and operating costs through smaller bed sizes and/or longer operating cycles.
  2. Low abrasion. Insures less dusting during tower depressurization or loading. Low abrasion means low pressure drop and a reduced chance of plugging the afterfilter.
  3. Resists liquid water. Water slugging due to upstream failure of aftercooler, separators or drain traps will not fracture. The adsorption capacity of the desiccant can be restored after complete regeneration.
  4. High crush strength. High crush strength, which limits dusting, is important during loading of desiccant towers. High crush strength makes effective as a prebed material when used with other types of desiccants.
  5. Uniform bead sizes. Is a uniformly sized bead. It provides low pressure drop to minimize channeling and ensures utilization of the full bed column section.

Physical Properties:

  1/8” (2-5mm) 3/16”(4-8mm) 1/4” (5-10mm)
Color and form  White  bead  White  bead  White  bead
 Bulk density  48 lbs/Ft3  48 lbs/Ft3  48 lbs/Ft3
 Crush strength  17-30 lbs 145-60 lbs 50-70 lbs
 Surface area  1.74 x 106 sq ft/lb  1.65 x 106 sq ft/lb  1.59 x 106 sq ft/lb
 Static adsorption
 Humidity
 		             -            -              -
100% RH
90% RH
60% RH
10% RH		 42.0%
37.5%
21.0%
7.5%		 40.0%
35.0%
21.0%
7.0%		 36.0%
32.0%
17.5%
6.0%
 
Product Note:
Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates