Product Short Description: A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
Product Description:

A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.

It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.

Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.

Product Application:

• Use cold - no heating required.
• Easily dissolves deposits containing carbon , polymer resin etc.
• Economical to use.
• Scraping not required.
• Non- flammable.
• Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
• Cleans oil side of fuel heaters, oil coolers, etc.
• Can be used for cleaning of : -Fuel Oil Filters - Pistons - Piston rings - Valve cage

Product Dose:

Directions for Use and Dose Rates

Soak Method:-
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201. can be used undiluted especially when deposition is heavy and hard spots persist.

Cleaning Procedure

Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201 is sufficient to cover a surface area of 8–10 square meters.


NOTE ::: -- Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.

Note:-
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.

Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.

Product Note:

   **Read the Material Safety Data Sheet before using this product.**

Other Valuable Hold Cleaners :::

Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020,  Part No.- RXSOL-22-2202-050

Part No.- RXSOL-22-2202-035, Part No.- RXSOL-22-2202-210
 
 
Slip Coat RXSOL HOLD BLOCK  ::: Polymer EMULSION BASED non reactive coating materials which makes thin film barrier on surface after dry. Due to formation of RXSOL THIN barrier film on surface, the cleaning operation after unloading becomes quicker and easier with optimum results. Part No.- RXSOL-22-2210-210, Part No.- RXSOL-22-2210-025, Part No.- RXSOL-22-2210-050
 
BARRIER HOLD COAT ::: Highly effective ecofriendly Product blending of natural ingredients which is provide thin temprory film on Hold Surface to protect corrosion. This is making barrier between corrosive cargo like Sulphur, Salt, Petcoak, Cement etc and Hold surface. Part No.- RXSOL-22-2211-210
 
COAL REMOVER rx hold  ::: A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems. Part No.- RXSOL-22-2215-210, Part No.- RXSOL-22-2201-025, Part No.- RXSOL-22-2201-050
 
 
Hold Wash Concentrate RX ::: RXSOL hold wash is a versatile all purpose marine cleaning solution it can be used as a powerful st
Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates